TCS Z2 in an Atlas SD35

As I model the Southern Pacific, many of my engines have the nose lights modeled but not lighted.  It's easy to add this type of lighting when installing a decoder using one of the pre-wired surface mount LEDs.





As this installation is otherwise very similar to several others I have presented, I will skip over some of the common points and focus more on what is unique to this installation. See my posts on the Atlas SD50 and GP40 for details of the basic decoder installation.

Once the shell is off a quick check of the mechanism indicates that there is room for a small wired decoder like the TCS Z2.

The original Atlas LED board is used after all of the modifications shown in this photo are done.  Note that an additional hole is made in the front part of the board for the nose LED wires.

This is also the time to replace the stock LED's with bright white LED's if desired.

While no modifications to the frame are needed for a standard installation, I did make grooves on the front of the left.frame for the LED and it's wires.

This photo shows what I had to do to the frame and the type of LED I used.

Here is a look at how the nose light LED is installed and connected to the LED on the board.  The ends of the wires will need about 1/8 inch of the insulating enamel scraped off before they can be soldered on the board.


Using a Z2 decoder and wiring this extra LED in parallel will mean that the nose LED will turn ON and OFF with the F0 function.

TCS Z2 in a Bachmann Spectrum 44 tonner

It's been a couple of months since I've posted anything but I have been kept busy with installs.  They've mostly been routine ones that I had already covered on this blog.   But recently I was asked to replace the decoder in a Bachmann Spectrum 44 ton switcher with a TCS Z2 or similar small decoder.

I was not very familiar with this model so I checked it out on the web.  It seems that Bachmann offered this model only in a DCC version and that no DCC manufacturer offers a replacement decoder.  Also on some of the forums there was mention of problems with programming this decoder.

This model uses the tested method of bumps on the frame / dimples on the inside of the shell to hold the shell in place.  It's a tight fit and after trying a few methods to get the shell off,  this was the one I found the easiest.

The trucks will come off fairly easy so I took them off first then placed a jewelers screwdriver between the fuel tank and the shell and gently pried.

Once the shell is off, we can see the original decoder board.  The decoder is secured to the frame with 2 small screws, one on each frame half.

The decoder has mostly surface mount components with a couple of coils on the bottom and what the instruction sheet called a thermal fuse link in series with the motor.

The way this component was installed in the motor wiring instead of on the board suggest to me that it may have been an after thought.

I made two custom LED boards from a two stock Kato LED boards that I had in my collection.  This photo shows the modifications I made to get what I wanted.

Here are the 2 new LED boards that I made from a Kato LED boards.  Don't know what engine it originally came from.  I wanted something with surface mounted LED's.  The new boards are secured to the frame by the original screws and provide track connection to the decoder.  I spliced the decoder wires onto the motor wires so I would not have to remove the motor.

Here's the side view of the finished mechanism.  One of the nice things about the LED boards I made was that they are single sided meaning that I don't have to worry about anything on the bottom shorting on the frame.  The space where the coils of the old decoder were could be used to add a bit of weight.

The inside of the shell of this loco offers an opportunity to add quite a bit of weight to this loco in the cab where the black plastic box that was attached to the original decoder had been.   I painted the inside of the cab windows a dark gray, then attached 2 layers of lead strip to the roof.   Another area where weight can be added is along the inside of the cab side walls below the side windows.

If the replacement LED boards, decoder, and wires are not interfering with the shells fit, the shell should rest on the parts of the frame that stick out as shown in this photo.

Here is the completed engine.  With the weight that was added it is close to the same weight as a stock Life Like SW type switcher and has about the same pulling power.

TCS CN-GP in an Atlas SD9

The Atlas SD7 and SD9 releases from the early 1990's that were made by Kato work very well with the TCS CN-GP decoder.  This example uses an SD9 but the mechanism is identical for the SD7.  First step is to completely disassemble the locomotive.

Only a few minor modifications are needed on the frame at the locations indicated in this photo.  I use a Dermal rotary tool with a cutoff wheel to do this and then I smooth things out with a jewelers file.



In this photo the modifications have been completed.   Be sure that the frame sides are free of any loose bits of metal before re-assembly.  An old paint brush works well for this.








After removing the brushes from the motor, file a groove from top to bottom of the motor as shown in this photo.  It should be large enough for 1 of the decoder wires to fit in it.  It's important that this wire does not get pinched between the motor and frame after the engine is re-assembled.





To test that the wire has clearance, thread a scrap of decoder wire through the motor saddle, around the motor and groove as shown with the motor and motor saddle temporally re-installed in the left side frame.  The wire should move freely.





Next remove the orange & gray motor wires from the front decoder board and solder them to the brush caps.  Re-install the brushes without the contact tabs.


Secure the wire from the bottom of the motor in the groove with adhesive of your choice.  I've used Walthers to do this but lately I've been using E6000 which I purchased at Tap Plastics.




Install the motor assembly, and worm gears into the left side frame as shown here.  The motor wires should come out of the notch on the top of the frame and not be pinched in any way.



Reassemble the frame sides and install the trucks, contact strips, and fuel tank.  Leaving the motor wires long, solder them temporarily to the points shown here to test run the engine.  If it runs backwards then reverse the motor wires at the decoder.












Here is the completed installation less the engine shell.  The wires must lay flat on the top of the frame for the shell to sit correctly.  There is a bit of room for extra weight if desired.

TCS Z2 in a Micro Trains FT

Anyone who has followed this blog will notice that I am a fan of TCS decoders and use a lot of their Z2 model.  I have found it to be a great decoder, small enough for many applications and robust enough for any N scale engine.  TCS does not make a board type decoder for the Micro Trains FT so I wanted to see if I could wire in a Z2 and found it to be a relatively easy install.

The first step is to remove the shell from the frame.  On the front of the A unit, remove the screw then pull the coupler out forward.

On the rear of the A unit and both ends of the B unit, removed the coupler and mounting frame together.

After removing the shell, the LED light board is exposed.  Just behind the board there is an indent in the frame that is large enough for a wired decoder.  Remove the black light shield and then the board. That's right, the frame won't have to be taken apart on this one.



The boards in the A units will have the LED along with a couple of other components.  Remove the two that are pointed out in this photo.  They were needed for the DC operation of the bright white LED but will not be needed for the decoder function output. 

The board from a B unit will not have any components on it at all so this step can be skipped.










I have found the quickest way to isolate all the parts of the board is to cut a notch on each side of the board through the two circuit traces.

This step needs to be done on the boards for both the A and B units.








Here are the lengths I cut the wires to. 

Blue, white, gray, yellow = 1"
Orange = 1-3/8"
Red, black = 1-5/8"








Kapton tape is best to use for insulating the frame but does not stick to the frame as well as Scotch tape.  I clean any oil off the frame of course, but then I use a layer of Scotch tape first then apply the Kapton tape.  It sticks very well to the first layer.

Connect all of the decoder wires as shown in this photo.  This can be done either before or after the board is re-installed in the engine.  The photo shows an A unit.  The B unit won't need the white and blue wires.

Special note on the B units

FT's were run with the B units oriented backwards in relation to their associated A unit and were often draw bared together.  This is noticeable by the two sets of ladders, the offset of the wheels and fuel tank, and the dynamic brake vents on the roofs of the ones that had dynamic brakes.  The PC board in the Micro Trains FT B unit is oriented in the opposite direction as the A unit.  This would have not mattered running DC but with DCC we must have a front and a back end to each locomotive.

Here is a prototype photo showing an A B set arranged this way.

This photo showing an A B set with the shells next to a pair of mechanisms shows what is going on.  This can be corrected by programming the B unit for reverse operation

CV 29 = 07 for 2 digit address
CV 29 = 27 for 4 digit address

TCS CN-GP in an Atlas GP7

Between 1995 and 1997 Atlas did several releases of N Scale GP7's and GP9's based upon this mechanism.  The TCS CN-GP decoder is a perfect choice for these. 

The frame requires some very minor modifications that I do using a Dermal rotary tool with cutoff wheel.  The small ridges between the light board clips at each end will need to be removed and also a notch needs to be made on the left side frame at the point shown in this photo.

On some GP9 releases the frames have interlocking tabs.  If you have one of these just snap off the upper tab.  This will create the space needed for the motor wires.






In this photo all of the frame modifications are done.  Also shown is the plastic motor saddle with a  notch on the top.  The notches on the frame and the saddle are needed for the motor wires.

Remove the brush caps from the motor and remove or cut the contact tabs.  Then remove the orange and gray wires from the decoder and solder them to the brush caps.  File a slot big enough for 1 wire on the left side of the motor.  With the orange wire going to the bottom, re-install the brush caps with wires and motor saddle.

Re-assemble the locomotive mechanism with the orange and gray wires going through the hole on the top of the left side frame and the plastic motor saddle.

Install the CN-GP decoder boards on the frame and connect the yellow, black, and blue wires as directed in the decoder instruction sheet.
Cut the orange and gray wires to the correct length and re-solder to the front board.  All wires should lay flat and not overlap on the top of the frame.

Re-install the trucks, contact strips, and fuel tank.

These Atlas GP7's were among the first N scale engines to have lighted number boards with the numbers already in them.  Because the LED they used was so dim, this feature was not really noticeable.


With the bright white LED's that come with the CN-GP decoder, this feature can now be fully appreciated as seen in the photo above.  You may even find it necessary to mask for paint the inside of the shell at the ends if the light shines through the shell.

TCS Z2 in an older Atlas RS11

This is an old engine without the LED lights, flywheels, low friction trucks, or Micro-Trains ready coupler pockets that we have become accustomed to.  At about the time DCC started to catch on with N scalers in the early 1990's, this was a very common mechanism that was used on several models made for Atlas by Kato in the mid to late 1980's.   They do have a good motor, and with a DCC decoder momentum can be programmed to help make up for the lack of flywheels.

First step is to take the engine apart.  Getting the shell off is the hardest part.  Here's the trick.  First remove the cab to expose the catches that hold the shell to the frame.







Once the cab is off, the main part of the shell can be easily removed as shown in this photo.







This photo shows all of the parts after this RS11 has been dis-assembled.

This mechanism is almost identical for the Kato made Atlas RS3, RS11, RSD4/5, RSD12, GP7, and GP9.





Here are the lengths that I cut the decoder wires to.

2" - White
1-7/8" - Red & Black
1-3/4" - Orange
1-1/4" - Gray
7/8" - Yellow & Blue


This photo shows the decoder wires solder to the modified light boards and the motor brush caps.


The next two photos show the details of the light boards.

The PC boards are the same as the common Kato 77A board.  It's just that these have a light bulb and a diode instead of a LED and resistor.  The directional lighting will be determined by the decoder so the diodes are not needed.

The red and black wires from the decoder will make their connection to the frame from this board.




On the rear light board I cut off the tabs with a Dermal tool, removed the diode and soldered the blue and yellow wires from the decoder to the light.  Polarity will not matter with the light bulb.  A second blue wire was run between this board and the front board.










Re-install the brush caps with the brushes and springs on the motor.  Then place the motor assembly into the left side frame as shown in this photo.  This one did not have any separate worm gears or bushings, it was all attached to the motor.










Here is the completed DCC mechanism.  As you can see, there is lots of room for the decoder.  Any of the small wired N or Z scale decoders could fit in this space.



Finishing Touch

These older engines had truck mounted Rapido couplers with big openings on the pilots.

Micro-Trains made pilot conversion kits and these are still available.  For the RS11 look for Micro-Trains part number 1150.

TCS Z2 in a Life Like C-Liner

We start a new year of installing DCC decoders in N scale locomotives.  This year will be almost all new material as I think I've used almost all the old material I once had on the nscalestation web site. 

First up will be the Life Like C-Liner

I sent the frames to Aztec Mfg for milling.  This photo shows what is removed from the frame.  Because of the way the motor mounts into the frame with no plastic saddle, the space around the motor is tight and it's important to have the spaces milled around the motor so the brush caps don't touch and wires don't get pinched.


Just like I do with Kato F units, I take the extra step to drill and tap holes for size 2-56 screws that will be used to attach the decoder wires securely to the frame.  This would be a requirement on the B's anyway because there is no light board so I just do it for both A's and B's.


In this case I am using a TCS Z2 but any of the small decoders available today should fit in the space provided.

The wires are cut to the lengths indicated in this photo.  Then the brush cap are removed from the motor and the orange and gray wires soldered to those.  The motor brush contacts that are removed with the brush caps and then soldered to the red and black wires.  These will be secured by the screws to the frame to provide a reliable connection.










This step is done on A units only.  With a Dermal motor tool and a cutoff wheel, I remove the circuit traces that could connect the board to the frame.  Then I also make a notch in the front edge of the board that the blue and white wires pass through.  The blue and white wires are then soldered to the board as shown in this photo.  On this one I kept the light stock light bulb so a resistor is not needed.



After re-installing the motor brushes into the motor, the motor, gears, and bushings are all re-installed into the right side frame as shown in this photo.  Take care that the orange wire is in the channel and not being pinched between the motor and frame.  This model has a spacer with an odd shape that goes on the front.  Notice the orientation of the spacer.

Install the left side frame and install the nuts and screws.  Then use the 2-56 x 1/4" screws to secure the red wire to the right side frame and the black wire to the left side frame.





This is the completed mechanism for a C-Liner A.  Double stick tape is used to secure the decoder and wires. Test run the mechanism then if satisfied with the way it runs, install the shell. The shell on this model goes on straight down so that ribs inside the shell fit into slots on each side of the frame.